TD62M2702F 2001-07-05 1 toshiba bipolar digital integrated circuit multi chip TD62M2702F low saturation voltage h ? bridge driver TD62M2702F is short break use multi ? chip driver ic incorporates 2 schottky barrier diodes and 4 low saturation discrete transistors which equipped bias ? resistor and fly ? wheel diode. this ic is suitable for forward ? reverse control on a battery use motor drive applications. features built ? in fly ? wheel diode (upper side) built ? in schottky barrier diode (lower side) built ? in bias resistor (upper side) : r = 1 0 k ? (typ.) ssop 1 6 ( 1 mm pitch) small package sealed low saturation voltage block diagram pin connection (top view) weight: 0.14 g (typ.)
TD62M2702F 2001-07-05 2 maximum ratings (ta = 25c) characteristic symbol rating unit supply voltage v cc 10 v v cbo 10 v cer 10 breakdown voltage v ebo 6 v i out 2 output current i o (peak) 4 (note 1) a i b 0.4 base current i b (peak) 0.8 (note 1) a diode forward current i f 2 (note 2) a power dissipation p d 490 mw junction temperature t j 125 c operating temperature t opr ? 40~85 c storage temperature t stg ? 55~150 c note 1: t = 10 ms max. and maximum duty is less than 30%. note 2: t = 10 ms single pulse electrical characteristics (ta = 25c) characteristic symbol test cir ? cuit test condition min typ. max unit upper side h fe (1) D v ce = 1 v, i c = 0.5 a 160 D 600 lower side h fe (1) D v ce = 1 v, i c = 0.5 a 200 D 650 current gain h fe (2) D v ce = 1 v, i c = 2.0 a 60 130 D D i c = 1 a, i b = 25 ma D 0.1 0.22 upper side i c = 2 a, i b = 50 ma D 0.2 0.45 i c = 1 a, i b = 25 ma D 0.1 0.22 lower side i c = 2 a, i b = 50 ma D 0.2 0.45 i c = 1 a, i b = 25 ma D 0.2 0.42 saturation voltage summing total v ce (sat) D i c = 2 a, i b = 50 ma D 0.4 0.85 v transition frequency f t D v ce = 2 v, i c = 0.5 a D 150 D mhz upper side D 0 5 lower side D D 200 leakage current v cc ? gnd i ol D v cc = 10 v D D 5 a i f = 300 ma D 0.89 1.2 upper side i f = 450 ma, 10 ms D 1.60 D diode forward voltage (note) lower side v f D i f = 1 a D D 0.58 v base ? emitter resistance r be D D 7 10 13 k ? base ? emitter forward voltage v be D v ce = 1 v, i c = 2 a D 0.84 1.5 v note: schottky diode u1fw49 (no heat sink) is guaranteed at v f (lower side) = 0.55 v (max.) but the TD62M2702F is guaranteed at v f (lower side) = 0.58 v (max.) (voltage shift of 0.03 v (i f = 1 a) is due to different package.)
TD62M2702F 2001-07-05 3 precautions for using this ic does not integrate protection circuits such as overcurrent and overvoltage protectors. thus, if excess current or voltage is applied to the ic, the ic may be damaged. please design the ic so that excess current or voltage will not be applied to the ic. utmost care is necessary in the design of the output line, v cc and gnd line since ic may be destroyed due to short ? circuit between outputs, air contamination fault, or fault by improper grounding.
TD62M2702F 2001-07-05 4 package dimensions ssop16 ? p ? 225 ? 1.00a unit: mm weight: 0.14 g (typ.)
TD62M2702F 2001-07-05 5 toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc.. the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk. the products described in this document are subject to the foreign exchange and foreign trade laws. the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba corporation for any infringements of intellectual property or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any intellectual property or other rights of toshiba corporation or others. the information contained herein is subject to change without notice. 000707eb a restrictions on product use
|
